Hollow multi-nanochannel carbon nanofiber/MoS2 nanoflower composites as binder-free lithium-ion battery anodes with high capacity and ultralong-cycle life at large current density

The electrode materials with high pseudocapacitance can enhance the rate capability and cycling stabil-ity of lithium-ion storage devices.Herein,we fabricated MoS2 nanoflowers with ultra-large interlayer spacing on N-doped hollow multi-nanochannel carbon nanofibers(F2-MoS2/NHMCFs)as freestanding binder-free anodes for lithium-ion batteries(LIBs).The ultra-large interlayer spacing(0.78～1.11 nm)of MoS2 nanoflowers can not only reduce the internal resistance,but also increase accessible active sur-face area,which ensures the fast Li+intercalation and deintercalation.The NHMCFs with hollow and multi-nanochannel structure can accommodate the large internal strain and volume change during lithi-ation/delithiation process,it is beneficial to improving the cycling stability of LIBs.Benefiting from the above combined structure merits,the F2-MoS2/NHMCFs electrodes deliver a high rate capability 832 mA h g-1 at 10 A g-1 and ultralong cycling stability with 99.29 and 91.60％capacity retention at 10 A g-1 after 1000 and 2000 cycles,respectively.It is one of the largest capacities and best cycling stability at 10 A g-1 ever reported to date,indicating the freestanding F2-MoS2/NHMCFs electrodes have potential applications in high power density LIBs.     

氧化铝纤维束织造过程中摩擦磨损性能研究

运用往复线性摩擦试验方法,搭配自制的摩擦试验夹具,模拟织造过程中氧化铝纤维束-筘齿的摩擦行为,研究加载力、预加张力和摩擦频率对悬空状态下氧化铝纤维束摩擦磨损性能的影响.结果表明:随着加载力的增加,氧化铝纤维束所受摩擦力及长丝断裂根数增加,摩擦系数减小;在预加张力为0.40 N时,氧化铝纤维束所受摩擦力和摩擦系数出现最小值,磨损程度也最小;在摩擦稳定阶段,摩擦频率增加,则氧化铝纤维束所受摩擦力先下降,后略有上升,当摩擦频率增加至5 Hz时,氧化铝纤维束的摩擦系数较1 Hz时增加18.7％,磨损程度也最为严重.     

Design and optimization of ceramic membrane structure: From the perspective of flux matching between support and membrane

The support flux was first investigated as a separate influencing factor for its effect on performances of ceramic filtration membranes. Three pre-membranes were prepared by tape-casting and then transfer-coated to supports to form dual-layer ceramic membranes after sintering. Experiments demonstrated that membrane layers with almost the same properties were obtained despite the huge difference in support flux. When the support flux increases from 3.120 to 97.53 m³m^?2h^?1, the flux of these three membrane series have increased by 75%, 186% and 228%, respectively. Experimental rules can provide structural design and evaluation from the perspective of permeability. The limit membrane flux of a certain system was derived according to the resistance distribution law of internal membrane structure and the Darcy's theorem. On this basis, a method for designing support flux was proposed. Furthermore, we present a criterion to quickly and easily evaluate the match between the support and the top layer, which is the ratio of membrane resistance to total resistance. Finally, the filtration resistance of penetration caused by suction of membrane particles into the support was measured for the first time, taking the advantage of the transfer-coating method that inherently free of penetration. Our works are expected to deepen the understanding of the ceramic membrane structure and provided guidance for its rational design and optimization.     

New optical ceramics: High-entropy sesquioxide X2O3 multi-wavelength emission phosphor transparent ceramics

Highly transparent X₂O₃ sesquioxide ceramics were obtained from a solid solution of five different oxides (Lu₂O₃, Y₂O₃, Yb₂O₃, Gd₂O₃, and Dy₂O₃), mixed in an equal molar ratio according to the principle of high-entropy. The fabricated (Lu, Y, Yb, Gd, Dy)₂O₃ ceramics achieved 99.97 % of the relative density and exhibited a high degree of optical transparency with the in-line transmittance of almost 80 % in the visible wavelength range. Emissions of Gd³⁺ (⁶P_J → ⁸S_7/2 at 312 nm), Dy³⁺ (⁴F_9/2 → ⁶H_15/2 at 492 nm and ⁴F_9/2 → ⁶H_13/2 at 572 nm), and Yb³⁺ (²F_5/2 → ²F_7/2 at 1031 nm) suggested a potential application of the high-entropy ceramics as multi-wavelength emission phosphor transparent ceramics. High-entropy ceramics also exhibited lower specific heat and thermal conductivity compared to single-element sesquioxide ceramics. This work demonstrated that highly transparent oxide ceramics, with complex chemical compositions and good optical properties, could be obtained using the high-entropy principle.     

Eco-friendly and degradable red phosphorus nanoparticles for rapid microbial sterilization under visible light

Pathogens pose a serious challenge to environmental sanitation and a threat to public health.The frequent use of chemicals for sterilization in recent years has not only caused secondary damage to the environment but also increased pathogen resistance to drugs,which further threatens public health.To address this issue,the use of non-chemical antibacterial means has become a new trend for environmental disinfection.In this study,we developed red phosphorus nanoparticles(RPNPs),a safe and degradable photosensitive material with good photocatalytic and photothermal properties.The red phosphorus nanoparticles were prepared using a template method and ultrasonication.Under the irradiation of simulated sunlight for 20 min,the RPNPs exhibited an efficiency of 99.98%in killing Staphylococcus aureus due to their excellent photocatalytic and photothermal abilities.Transmission electron microscopy and ultraviolet–visible spectroscopy revealed that the RPNPs exhibited degradability within eight weeks.Both the RPNPs and their degradation products were nontoxic to fibroblast cells.Therefore,such RPNPs are expected to be used as a new type of low-cost,efficient,degradable,biocompatible,and eco-friendly photosensitive material for environmental disinfection.     

A Biologically Muscle-Inspired Polyurethane with Super-Tough,Thermal Reparable and Self-Healing Capabilities for Stretchable Electronics

Polymeric elastomers play an increasingly important role in the development of stretchable electronics. A highly demanded elastic matrix is preferred to own not only excellent mechanical properties, but also additional features like high toughness and fast self-healing. Here, a polyurethane (DA-PU) is synthesized with donor and acceptor groups alternately distributed along the main chain to achieve both intra-chain and inter-chain donor-acceptor self-assembly, which endow the polyurethane with toughness, self-healing, and, more interestingly, thermal repair, like human muscle. In detail, DA-PU exhibits an amazing mechanical performance with elongation at break of 1900% and toughness of 175.9 MJ m⁻³. Moreover, it shows remarkable anti-fatigue and anti-stress relaxation properties as manifested by cyclic tensile and stress relaxation tests, respectively. Even in case of large strain deformation or long-time stretch, it can almost completely restore to original length by thermal repair at 60 °C in 60 s. The self-healing speed of DA-PU is gradually enhanced with the increasing temperature, and can be 1.0–6.15 µm min⁻¹ from 60 to 80 °C. At last, a stretchable and self-healable capacitive sensor is constructed and evaluated to prove that DA-PU matrix can ensure the stability of electronics even after critical deformation and cut off.     

The spheroidization process of micron-scaled α-Al2O3 powder in hydrothermal method

Understanding the spheroidization process of micron-scaled α-Al₂O₃ powder in hydrothermal method is of great importance but still not completely revealed. The results demonstrated that SO₄^2? played a significant role in the formation of spherical powder, while the bubble generated from the reaction of urea didn't work in the spheroidization process. The spheroidization process was summed up as two steps. The first was that SO₄^2? limited the hydrolysis of Al³⁺ and reacted with Al³⁺ and OH^- to form Al₄(OH)₁₀SO₄, which nucleated and agglomerated into granular precipitates. The second was Ostwald ripening, which gave the spherical precursors a double-layered structure. When the spherical precursors obtained 120 °C were sintered at 1200 °C, α-Al₂O₃ were got and the spherical morphology still maintained with a large number of nano-sized pores. We anticipate the spherical α-Al₂O₃ with nano-sized pores can be applied in adsorption and filtration industries.     

妈祖文化视域下的表情符号设计研究

目的 基于妈祖文化的视角,探究妈祖文化与表情符号设计融合的可能性,打造表情文化产业链,为表情符号的设计开发提供更多的机遇,推动了妈祖文化的对外传播.方法 以妈祖文化为切入点,分析表情符号设计与妈祖文化跨界融合发展的优势.同时,借助具体的案例来阐述两者结合所产生的积极意义,表明巧妙应用妈祖文化的可行性.结论 妈祖文化的融入为表情符号的发展增添了浓墨重彩的一笔,对于增强文化气息及开拓设计思路都发挥着重要作用,易于激发受众的情绪、记忆,引起受众情感和心理的共鸣,从而创造符合受众审美情趣和思维方式的设计作品.由此可见,深入把握两者的关联性,有助于催生新的文化产业形态、传承妈祖文化、开辟表情符号设计新路径.     

Preparation and antifouling performance of thin inorganic ultrafiltration membrane via assisted sol-gel method with different composition of dual additives

A novel TiO₂ thin film was prepared on the ceramic hollow fiber by the sol-gel method using poly(vinylpyrrolidone) (PVP) and polyvinyl alcohol (PVA) as additives. SEM images verified the formation of TiO₂ layer with various thickness using different composition of titania sols. The effect of the PVP and PVA contents on the TiO₂ sol properties, the separation and the antifouling performance of the ultrafiltration membranes were investigated thoroughly. When the contents of PVP and PVA were 1.0 wt% and 0.8 wt%, respectively, the resultant membrane showed a thickness of 0.55 μm with a pure water flux of 255 L m^?2 h^?1. In addition, the adherent foulant bovine serum albumin was applied to evaluate the antifouling performance. During the three fouling-recovery cycles, the flux recovery ratio and the flux decay ratio maintained about 99% and 30%. The BSA flux and rejection were still 169 L m^?2 h^?1 and 96.9% after the cycles, indicating a superior antifouling property.     

Fabrication of bacterial cellulose with high efficient loading of Ag and TiO2 nanoparticles for removing organic dyes

As a new advanced oxidation technology, photocatalytic technology has broad application prospects in the field of wastewater treatment. However, in the actual use process, there will be difficulties in catalyst recovery and reuse. This article successfully prepared bacterial cellulose (BC) loaded silver and titanium dioxide nanoparticles (Ag-plated TiO₂/BC composite pellicle) by in situ embedding method. BC not only works as the carrier to load TiO₂ and Ag NPs but also adsorbs dyes to promote the reaction. As a reusable photocatalytic film, it is convenient to use and recycle in terms of testing and characterization compared with powders. The results show that Ag and TiO₂ nanoparticles were closely embedded in BC. We evaluated the photocatalytic degradation performance of the catalyst on methylene blue (MB), active red X-3B, and Rhodamine B. When the reaction time was 2 h, the dye removal rates were 71%, 68%, and 82.6%. At the same time, through the inhibition zone experiment, it was found that the material has a certain inhibitory effect on both Escherichia coli and Staphylococcus aureus. Therefore, the supported catalyst prepared by this method has the advantages of high catalytic activity, relatively stable property, easy recovery, and tailorability, making it potentially applicable in sewage post-treatment links.